|
WASTE KING® EXCLUSIVES
Anti-Jam Swivel Impellers rotate out of the way of an
impending jam, then fall back into grinding position,
pulverizing waste particles.
Stainless Steel Undercutter Blade located beneath the grind
ring snips fibrous and stringy waste into small particles
making them less likely to clog drain lines.
Hush-Cushions® isolate the unit from metal to metal contact,
significantly reducing noise level. Hush-Cushions® are
specially compounded and designed to withstand vibration and
tension, and have a built-in safety splash guard.
FEATURES
- 1/2 HP disposer, dual voltage
- Fan cooled motor with ball bearing construction, and
integral overload protection
- Dynamically balanced for smooth, long wearing
operation
- Hush Cushion® mounting connection for 6" cone or
sink opening includes an auxiliary water inlet
- Stainless steel grind chamber
- Corrosion proof, glass reinforced polyester exit
chamber
- 5 3/8" Diameter stainless steel turntable
- 2 Jam resistant, hardened stainless steel swivel
impellers
- Stainless steel undercutter blade
- Hard, tough, cast alloy grind ring with dual stage
grinding action
- Lifetime particle size control by non-wearing exit
slots
MOUNTING SYSTEMS
Sink Mount Assembly (SM)
#2539 31/2" Bolt-in adapter for suspended models with 6"
throat
Trough Mount Assembly (TM)
#2536 6" Weld-in flange for models with 6" throat
Basic ConeAssembly (B)
12", 15", or 18" Cone with Swirl Sprays
All-Purpose Cone Assembly (AP)
12", 15", or 18" Cone with Swirl Sprays
Silver Guard
Scrap Ring
Dish Table Cone Assembly (DT)
12", 15", or 18" Cone with Swirl Sprays
12", 15", or 18" Cone Cover
Scrap Ring
PLUMBING
1/2 HP models are equipped with a drain outlet for
connection to a conventional 1 1/2" trap. The trap
may be connected to a 2" branch waste line running
directly into a waste stack. We recommend a slope in
the waste line of not less than 1/4" per foot.
Connect directly to waste line, not through a grease
interceptor.
MOTOR DATA 500-1 & 500-1SM (special order
ONLY)
60 cycle 1 Phase 1/2 HP 1725 RPM 110-120/220-240
volts 9.2/4.6 Amps Bearing permanently lubricated.
Manual reset overload protection in motor.
NOTE:
Disposer assembly includes disposer, mountings, and
drain outlet. Other items shown in gray are
available in mounting systems or ordered separately.
Installation should be made in accordance with local
codes. All specifications subject to change without
notice. Assembly should be installed in accordance
with Waste King's printed installation instructions.
* Items available through Waste King
|
 |
TO SPECIFIERS
So that you may be assured of receiving the fine quality
you expect when you specify a WASTE KING® FOOD WASTE REMOVAL
SYSTEM, we include the following sample specification for
your convenience: Food waste disposer shall be 1/2 HP, 60
cycle, I Phase with 110-120/220-240 volts. There shall be a
rubber Hush Cushion® between the disposer and the cone or
sink to eliminate metal to metal contact. Turntable shall be
of stainless steel with jam-resistant swivel impellers of
stainless steel and stainless steel cutting blade rotating
below the exit slots. Grind ring shall be precision ground
on all cutting surfaces and shall have non-wearing, size
controlled exit slots. Disposer shall have a totally
enclosed, continuous duty, fan cooled motor with integral
overload protection. Unit shall be Waste King® model 500-1.
ROUGH-IN DIMENSIONS With drain line connections
Cone Mounted Models
|
Sink Mounted Models with #2539 Sink Mount
Installation
|
BusBoy
Hammerall
InSinkerator
Master Disposer
Salvajor
Red Goat
Waste King
Hatco Booster Heaters
Disposer
Controls And Accessories By Manufacturer
|
