|
WASTE KING® EXCLUSIVES
Anti-Jam Swivel Impellers rotate out of the way of an
impending jam, then fall back into grinding position,
pulverizing waste particles.
Stainless Steel Undercutter Blade located beneath the grind
ring snips fibrous and stringy waste into small particles
making them less likely to clog drain lines.
Hush-Cushions® isolate the unit from metal to metal contact,
significantly reducing noise level. Hush-Cushions® are
specially compounded and designed to withstand vibration and
tension, and have a built-in safety splash guard.
FEATURES
- 1 1/2 HP disposer, dual voltage
- Fan cooled motor with ball bearing construction, and
integral overload protection
- Dynamically balanced for smooth, long wearing
operation
- Hush Cushion® mounting connection for 6" cone or
sink opening includes an auxiliary water inlet
- Stainless steel grind chamber
- Corrosion proof, glass reinforced polyester exit
chamber
- 6 1/4" Diameter heavy duty, cast stainless steel
turntable
- 2 Jam resistant, hardened stainless steel swivel
impellers with tungsten carbide inserts
- Stainless steel undercutter blade
- Hard, tough, cast alloy grind ring with dual stage
grinding action
- Lifetime particle size control by non-wearing exit
slots
MOUNTING SYSTEMS
Sink Mount Assembly (SM)
#2539 3 1/2" Bolt-in adapter for suspended models with 6"
throat
Trough Mount Assembly (TM)
#2536 6" Weld-in flange for models with 6" throat
Basic ConeAssembly (B)
12", 15", or 18" Cone with Swirl Sprays
All-Purpose Cone Assembly (AP)
12", 15", or 18" Cone with Swirl Sprays
Silver Guard
Scrap Ring
Dish Table Cone Assembly (DT)
12", 15", or 18" Cone with Swirl Sprays
12", 15", or 18" Cone Cover
Scrap Ring
PLUMBING
Models 1500-1 and 1500-3 are equipped with a drain
outlet for connection to a conventional 1 1/2" trap.
The trap may be connected to a 2" branch waste line
running directly into a waste stack. We recommend a
slope in the waste line of not less than 1/4" per
foot. Connect directly to waste line, not through a
grease interceptor.
MOTOR DATA
1500-1 60 cycle 1 Phase 1 1/2 HP 1725 RPM
110-120/220-240 volts 14.4/7.2 amps
1500-3 60 cycle 3 Phase 1 1/2 HP 1725 RPM
208-240/460 volts 4.4/2.2 amps
Bearing permanently lubricated. Manual reset
overload protection in motor.
NOTE:
Disposer assembly includes disposer, mountings, and
drain outlet. Other items shown in gray are
available in mounting systems or ordered separately.
Installation should be made in accordance with local
codes. All specifications subject to change without
notice. Assembly should be installed in accordance
with Waste King's printed installation instructions.
* Items available through Waste King
|
 |
TO SPECIFIERS
So that you may be assured of receiving the fine quality
you expect when you specify a WASTE KING® FOOD WASTE REMOVAL
SYSTEM, we include the following sample specification for
your convenience: Food waste disposer shall be 1 1/2 HP, 60
cycle, 1 Phase with 110-120/220-240 volts, or 3 Phase with
208-240/460 volts. There shall be a rubber Hush Cushion®
between the disposer and the cone or sink to eliminate metal
to metal contact. Turntable shall be of stainless steel with
jam-resistant swivel impellers of hardened stainless steel
with Tungsten carbide inserts. Turntable shall have
stainless steel cutting blades rotating below the exit slots
Grind ring shall be precision ground on all cutting surfaces
and shall have non-wearing, size controlled exit slots.
Disposer shall have a totally enclosed, continuous duty, fan
cooled motor with integral overload protection. Unit shall
be Waste King® model 1500-1 or 1500-3.
BusBoy
Hammerall
InSinkerator
Master Disposer
Salvajor
Red Goat
Waste King
Hatco Booster Heaters
Disposer
Controls And Accessories By Manufacturer
|
