|
WASTE KING® EXCLUSIVES
Anti-Jam Swivel Impellers rotate out of the way of an
impending jam, then fall back into grinding position,
pulverizing waste particles.
Stainless Steel Undercutter Blade located beneath the grind
ring snips fibrous and stringy waste into small particles
making them less likely to clog drain lines.
Hush-Cushions® isolate the unit from metal to metal contact,
significantly reducing noise level. Hush-Cushions® are
specially compounded and designed to withstand vibration and
tension, and have a built-in safety splash guard.
FEATURES
- 1 1/4 HP disposer, dual voltage
- Fan cooled motor with ball bearing construction, and
integral overload protection
- Dynamically balanced for smooth, long wearing
operation
- Hush Cushion® mounting connection for 6" cone or
sink opening includes an auxiliary water inlet
- Stainless steel grind chamber
- Corrosion proof, glass reinforced polyester exit
chamber
- 6 1/4" Diameter stainless steel turntable
- Ripper bar integrated with turntable
- 2 Jam resistant, hardened stainless steel swivel
impellers with tungsten carbide inserts
- 3 Stainless steel undercutter blades
- Hard, tough, cast alloy grind ring with dual stage
grinding action
- Lifetime particle size control by non-wearing exit
slots
MOUNTING SYSTEMS
Sink Mount Assembly (SM)
#2539 3 1/2" Bolt-in adapter for suspended models with 6"
throat
Trough Mount Assembly (TM)
#2536 6" Weld-in flange for models with 6" throat
Basic ConeAssembly (B)
12", 15", or 18" Cone with Swirl Sprays
All-Purpose Cone Assembly (AP)
12", 15", or 18" Cone with Swirl Sprays
Silver Guard
Scrap Ring
Dish Table Cone Assembly (DT)
12", 15", or 18" Cone with Swirl Sprays
12", 15", or 18" Cone Cover
Scrap Ring
PLUMBING
Models 1250-1 and 1250-3 are equipped with a drain
outlet for connection to a conventional 1 1/2" trap.
The trap may be connected to a 2" branch waste line
running directly into a waste stack. We recommend a
slope in the waste line of not less than 1/4" per
foot. Connect directly to waste line, not through a
grease interceptor.MOTOR DATA
1250-1 60 cycle 1 Phase 1 1/4 HP 1725 RPM
110-120/220-240 volts 12.8/6.4 amps
1250-3 60 cycle 3 Phase 1 1/4 HP 1725 RPM
208-240/460 volts 4.0/2.0 amps
Bearing permanently lubricated. Manual reset
overload protection in motor.
NOTE:
Disposer assembly includes disposer, mountings, and
drain outlet. Other items shown in gray are
available in mounting systems or ordered separately.
Installation should be made in accordance with local
codes. All specifications subject to change without
notice. Assembly should be installed in accordance
with Waste King's printed installation instructions.
* Items available through Waste King
|
 |
TO SPECIFIERS
So that you may be assured of receiving the fine quality
you expect when you specify a WASTE KING® FOOD WASTE REMOVAL
SYSTEM, we include the following sample specification for
your convenience: Food waste disposer shall be 1 1/4 HP, 60
cycle, 1 Phase with110-120/220-240 volts, or 3 Phase with
208-240/460 volts. There shall be a rubber Hush Cushion®
between the disposer and the cone or sink to eliminate metal
to metal contact. Turntable shall be of stainless steel with
jam-resistant swivel impellers of hardened stainless steel.
Turntable shall have stainless steel cutting blades rotating
below the exit slots Grind ring shall be precision ground on
all cutting surfaces and shall have non-wearing, size
controlled exit slots. Disposer shall have a totally
enclosed, continuous duty, fan cooled motor with integral
overload protection. Unit shall be Waste King® model
1250-1or 1250-3.
BusBoy
Hammerall
InSinkerator
Master Disposer
Salvajor
Red Goat
Waste King
Hatco Booster Heaters
Disposer
Controls And Accessories By Manufacturer
|
